This MSDS covers part numbers 40004R, 40016R, 40128R, 40640R,
43840R and 47040R for
Tap Magic Original Cutting Fluid. Click
for a printable PDF.
MATERIAL SAFETY DATA SHEET
U.S. DEPARTMENT OF LABOR, OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, HAZARD
COMMUNICATION STANDARD, 29 CFR 1910.1200
The Steco Corporation
2330 Cantrell Road
P.O. Box 2238
Little Rock, AR 72203
Emergency Response: (800) 255-3924
Information: (800) 643-8026
Fax #: (501) 374-4278
Date Reviewed: August 15, 2011
TRADE NAME: TAP MAGIC ORIGINAL Cutting Fluid
CHEMICAL NAME & SYNONYMS: Hydrocarbon Mixture
DOT SHIPPING NAME: 1,1,1-Trichloroethane Class 6.1 UN 2831, III
HMIS/NFPA CODE: Health 2; Fire 0; Reactivity 1; Specific - solvent
MANUFACTURING CODE NO.: 8358
COMMODITY CODE NO.: 332-9150
I. HAZARDOUS INGREDIENTS
1,1,1 Trichloroethane: CAS # 71-55-6 • OSHA PEL ppm, 350 • ACGIH
TLV ppm, 350 • Other limits recommended, STEL-450 • Max. %, 90.
Tert-butyl alcohol: CAS # 75-65-0 • OSHA PEL ppm, 100 • ACGIH
TLV ppm, 100 • Other limits recommended, STEL-150 • Max %, 3.
1,2-Butylene Oxide: CAS # 106-88-7 • OSHA PEL ppm, not listed •
ACGIH TLV ppm, Other limits recommended, est. STEL-100 • Max. %, 3.
Dimethoxymethane: CAS # 109-87-5 • OSHA PEL ppm, 1000 • ACGIH
TLV ppm, 1000 • Other limits recommended, STEL-1250 • Max. % 3.
Petroleum Oil, aliphatic: CAS # 68815-10-1 • OSHA PEL ppm, not listed
• ACGIH TLV ppm, not listed • Other limits recommended, not listed
• Max. %, 3.
Vegetable Oil, essential: CAS # 8007-80-5 • OSHA PEL ppm, not listed
• ACGIH TLV ppm, not listed • Other limits recommended, not listed
• Max. %, 3.
II. PHYSICAL DATA
BOILING RANGE, (760 mm, Mercury): 158-190 degrees F (70-80 C)
SPECIFIC GRAVITY (Water =1), lbs/gal.: (1.35), 11.3 lbs/gal.
VAPOR PRESSURE (mm of Mercury) @ 68 degrees F: 100
VAPOR DENSITY (Air = 1): 4.55
SOLUBILITY IN WATER, % by weight: 0.07
EVAPORATION RATE (Butyl Acetate = 1): 0.6 gal./sq.ft./day @ 76.6 F (24.4 C)
% VOLATILE BY VOLUME: Greater than 90%
APPEARANCE: Amber liquid, non-aqueous
ODOR: Aromatic
III. FIRE & EXPLOSION DATA
FLASH POINT, TOC, TCC, PMCC: None
AUTOIGNITION TEMPERATURE: None
EXTINGUISHING MEDIA: Water Fog
SPECIAL FIRE FIGHTING PROCEDURES: Positive pressure, self-contained respiratory
equipment
UNUSUAL FIRE AND EXPLOSION HAZARD: Product does not present any fire hazard,
however, when concentrated vapors are exposed to open flames or high energy
electrical arcs, irritating and toxic gasses (HCL) may be formed. Flammability
limits have been established utilizing high energy electrical arcs: LFL 6%;
UFL 16.7%.
IV. HEALTH HAZARD INFORMATION
ROUTES OF ENTRY: Exposure may occur via inhalation, skin contact or ingestion.
EFFECTS OF ACUTE OVEREXPOSURE:
INHALATION – Minimal anesthetic or narcotic effects may be seen in the
range of 500-1000 ppm. Progressively higher levels over 1000 ppm may cause
dizziness, drunkenness; concentrations as low as 10,000 ppm can cause unconsciousness
and death. In confined or poorly ventilated areas, vapors which readily accumulate
can cause unconsciousness and death. These high levels may also cause cardiac
arrhythmias (irregular heart beats).
SKIN CONTACT – A single prolonged skin exposure is not likely to result
in absorption of harmful amounts. The LD50 for rabbits is about 15,000 mg/kg.
INGESTION – Single dose oral toxicity is low. The LD50 for rats is greater
than 10,000 mg/kg. If aspirated (liquid enters lung), may be rapidly absorbed
through the lungs and result in injury to other body systems.
EYE – May cause pain and irritation with transient corneal injury.
EFFECTS OF CHRONIC OVEREXPOSURE:
SKIN CONTACT – Prolonged or repeated exposure may cause defatting of
the skin and subsequent rash or irritation.
ALL ROUTES OF ENTRY – Based on available data, repeated exposures are
not anticipated to cause any significant adverse effects. Birth defects are
unlikely. Exposures having no adverse effects on the mother should have no
effect on the fetus. In animal studies, has been shown not to interfere with
reproduction. Results of in vitro ("test tube") mutagenicity tests
have been negative. Results of mutagenicity tests in animals have been negative.
CARCINOGENICITY: Does not cause cancer in long term animal studies. Not a
carcinogen or suspect carcinogen.
EMERGENCY AND FIRST AID PROCEDURES:
EYE – Flush eyes gently with water for at least 15 minutes. Supportive
treatment is recommended by physician.
SKIN – Wash with mild soap and water. Remove wetted clothing until dry.
INHALATION – Remove to fresh air. Individuals showing pronounced anesthetic
effects may require artificial respiration and oxygen. Epinephrine and other
drugs with similar activity should not be administered.
INGESTION – Do not induce vomiting. Call a physician and/or transport
to emergency facility immediately
.
NOTES TO PHYSICIAN:
EYE – May cause Conjunctivitis, stain for evidence of corneal injury.
SKIN – May cause mild irritation, chronic exposure, defatting type of
Dermatitis, treat as any contact Dermatitis. Not likely to be absorbed in
acutely toxic amounts.
RESPIRATORY – Anesthetic or narcotic effect may occur, administer oxygen
if available. Bronchodilators, expectorants and antitussives may be of help.
ORAL – Low in toxicity. May cause reaction similar to petroleum or petroleum-like
solvent. Danger of chemical pneumonia must be weighed against toxicity when
considering emptying the stomach. If lavage is performed, suggest endotracheal
and/or esophagoscopic control.
SYSTEMIC – May increase myocardial irritability. Avoid Epinephrine or
similar acting drugs if at all possible. Consult standard literature. No specific
antidote. Treatment based on the sound judgment of the physician and the individual
reactions of the patient.
V. REACTIVITY DATA
STABILITY – The product is very stable under most conditions. Prolonged
storage in contact with water may cause some decomposition and the formation
of hydrochloric acid (when storing @ temperatures in excess of 150 F).Thermal
decomposition begins at 325 C (625 F).
INCOMPATIBILITY – Magnesium and aluminum are attacked at elevated temperatures.
Polystyrene, cellulose acetate propionate and polycarbonate plastics are dissolved.
Softens asphalt, swells natural or Buna rubber.
HAZARDOUS DECOMPOSITION PRODUCTS – When exposed to open flames (welding
torches) or high energy arcs, product may decompose yielding hydrogen chloride
(HCL) gas.
CONDITIONS CONTRIBUTING TO HAZARDOUS POLYMERIZATION –None
VI. DISPOSAL, SPILL OR LEAK PROCEDURES
AQUATIC TOXICITY – The product has a low biochemical oxygen demand (BOD),
does not interfere with biological treatment, and is easily aerated out of
water solutions. The odor threshold in water solution is 350 ppm.
SPILL OR LEAK PROCEDURES – For small spills, mop up, wipe up or soak
up immediately. Remove to out-of-doors. For large spills, evacuate area, contain
liquid and transfer to closed metal (steel)
container(s). Keep out of water supply. Reportable Quantity: 90 Gallons (1000
lbs.)
WASTE DISPOSAL METHOD – Very small amounts may be evaporated in compliance
with local, state and federal
regulations including Subtitle C of the Resource Conservation and Recovery
Act. Large quantities may be sent to a licensed reclaimer or permitted incinerators.
Never dump into sewers, on the ground or into any body of water. "If
inert absorbents are employed in spill containment or cleanup, these absorbents
must be non-biodegradable materials if destined for landfill disposal. Suitable
absorbents include natural minerals (clay), activated charcoal, man-made polymers
(HD polyethylene)."
NEUTRALIZATION CHEMICALS – Product may be effectively absorbed with
activated charcoal.
VII. SPECIAL PROTECTION INFORMATION
VENTILATION REQUIREMENTS – Normal ventilation with regular use to maintain
the TLV below recommended values (350 ppm).
SPECIFIC PERSONAL PROTECTIVE EQUIPMENT – RESPIRATORY: None during normal
use. When respiratory protection is required for certain operations, use an
approved air purifying respirator. For emergency conditions where the exposure
guideline may be greatly exceeded, use an approved positive pressure self-contained
breathing apparatus. • EYES: Single safety glasses to cup-type goggles
(precautionary measure due to machining operations). • GLOVES: Synthetic
rubber gloves, aprons and overshoes may be necessary to prevent excessive
skin contact when dealing with large spills (many gallons). • OTHER
CLOTHING & EQUIPMENT: None required.
VIII. SPECIAL PRECAUTIONS
Use with adequate ventilation. Avoid prolonged or repeated breathing of vapors.
Concentrated vapors are heavier than air and will collect in low areas such
as pits, degreasers, storage tanks and other confined areas. Large amounts
can displace oxygen in confined areas. Do not enter these areas where vapors
are suspected unless special breathing apparatus is used and an observer is
present for assistance. Avoid prolonged or repeated contact with skin. DO
NOT TAKE INTERNALLY. At elevated temperatures, aluminum may be corroded and
therefore, aluminum is not recommended for containers or handling equipment.
Ideally, a cool, dry, well ventilated storage area should be selected, however,
a properly sealed container may be stored under higher ambient temperatures
(150 F) and humid conditions without concern.
IX. ADDITIONAL REGULATORY CONCERNS
1,1,1-trichloroethane has been included by the EPA in a list of chemical compounds
designated as hazardous waste materials. This organic compound is highly volatile
and readily evaporates to the atmosphere. As a consequence, the potential
for contaminating an otherwise non-hazardous waste with 1,1,1-trichloroethane
originating from TAP MAGIC consumed during various machining operations is
small. RCRA hazardous waste no. U226.
SARA HAZARD CATEGORY: This product has been reviewed according to the EPA
'Hazard Categories' promulgated under Sections 311 and 312 of the Super Fund
Amendment and Reauthorization Act of 1986 (Sara Title III) and is considered,
under applicable definitions, to meet the following categories: An immediate
health hazard. This product contains toxic chemicals as listed in 40 CFR 372.65:
1,1,1-trichloroethane and 1,2-butylene oxide. TAP MAGIC ORIGINAL does not
contain any chemical compound listed on the SARA list of "Extremely Hazardous
Chemicals," and is in compliance with all of the requirements of the
TSCA at the time of shipment.
ADDITIONAL INFORMATION: TAP MAGIC does not contain Nitrites, Nitrite Derivatives,
Amines, Polynuclear
Aromatic Compounds or Benzene either as ingredients or as trace contaminants.
Shelf life is indefinite at ambient temperatures and left in original containers.
CAUTION: Any cutting fluid can be "overworked" or "overheated",
causing it to break down. This overuse is identified by the sight of or strong
odor of vapors or fumes not normally present. The effects of these vapors
or fumes on human health have not been fully determined. After use of this
product, clean and lubricate metal surfaces to avoid staining and/or corrosion.
___________________________________________________________________________________________________________
Prepared By : Asa L. Morton
Title : Chief Chemist
Company : American Interplex Corporation
Little Rock, AR 72204
Telephone : (501) 224-5060
| Tap
Magic Xtra-Foamy |
  |
|
|
||
|
||
|
||
|
||
|
||
|
||
|
||
|
||